微信红包

服务热线: 400-117-8816
           13406879330

ZHUANZHUYUNIUJIANXINGDIANDONGBANSHOU、NIUJIANXINGSHOUDONGBANSHOU、DINGNIUJUDIANDONGBANSHOU、NIUJUBEIZENGQIDEYANFAYUSHENGCHAN

当前位置:微信红包>技术文献>数控定扭矩电动扳手的注意事项

数控定扭矩电动扳手的注意事项

来源:http://fhgfx.com 日期:2021-03-09 发布人:admin

橡胶输送带在运行过程当中经常会接触到许多物料,时间长了之后输送带表面容易留下一些不好去除的污渍。污渍日积月累可能会将一些物料黏住,从而影响输送带的输送速度,严重的甚至可以造成输送带跑偏。因此输送带是需要定期清洗与维护的。下面,广州擎川橡胶给大家介绍一种比较简单的输送带清洗方法。

Rubber conveyor belt in the process of operation will often contact with many materials, after a long time, the surface of the conveyor belt is easy to leave some stains that are not easy to remove. The accumulation of stains may stick some materials, which will affect the conveying speed of the conveyor belt, and even cause the conveyor belt deviation. Therefore, the conveyor belt needs regular cleaning and maintenance. Next, Guangzhou Qingchuan rubber introduces a relatively simple cleaning method for conveyor belt.
首先,在清洗输送带前,所有不能涉水的设备都要用塑料薄膜包裹,防止进水造成电机短路,因为设备浸泡在水中后不能使用。
First of all, before cleaning the conveyor belt, all the equipment that cannot Wade should be wrapped with plastic film to prevent short circuit of the motor caused by water, because the equipment cannot be used after being immersed in water.
电动扭矩扳手
第二步、关闭蒸汽阀,查看张紧装置,调整设备压力。
Second, close the steam valve, check the tensioning device and adjust the equipment pressure.
第三步、检查一下输送带清洗机的状态情况,查看一下橡胶输送带的情况。如果输送设备上有零件损坏,必须提前修理好再清洗,否则会影响零件的使用。
The third step, check the status of the conveyor belt cleaning machine, check the situation of the rubber conveyor belt. If there are parts damaged on the conveying equipment, it must be repaired and cleaned in advance, otherwise the use of parts will be affected.
第四步、在清洗输送带之前先将输送带浸泡一会儿,清洗时会更加方便一些。
The fourth step, before cleaning the conveyor belt, soak the conveyor belt for a while, cleaning will be more convenient.
第五步、用低压喷枪均匀喷洒搅拌均匀的清洗液。千万不要使用高压喷枪,因为它会损坏输送皮带的表层。冲洗喷枪时,注意不要重复冲洗同一位置,并确保皮带的每个位置都可以冲洗。
The fifth step is to evenly spray the mixed cleaning solution with a low-pressure spray gun. Never use a high pressure spray gun as it will damage the surface of the conveyor belt. When flushing the spray gun, pay attention not to repeatedly flush the same position, and ensure that each position of the belt can be flushed.
第六步、上述操作完成后,用清水清洗皮带,检查皮带上的污渍,并干燥皮带以防发霉。
Step 6. After the above operation, clean the belt with clean water, check the stains on the belt, and dry the belt to prevent mildew.
总之,无论哪种设备都必须定期清洗,以保证长期使用,同时不会影响设备的工作效率。
In short, no matter what kind of equipment must be cleaned regularly to ensure long-term use, and will not affect the efficiency of the equipment.
今天是小编给大家介绍的电动扭矩扳手内容,更多的精彩内容请详细的关注我们的网站:http://fhgfx.com ,后续内容我们会定期的进行更新!
Today is the content of electric torque wrench introduced by Xiaobian. Please pay more attention to our website: http://fhgfx.com  We will update the follow-up content regularly!